GWR is continually posting new information to this section of our site, please be sure to refresh the page each time you visit.
 (Refresh by going to View then click Refresh) 

We manufacturer and distribute parts for most lathes including rubber, neoprene and spring silencer bands, hard parts for repairing the lathes, High Performance adapter sets and unique up-grade kits that improve lathe performance.   You will always save 25% to over 60% on factory replacement parts and tools for your lathe while maintaining OE quality or better.   Please call us with descriptions or part numbers and we will save you money with just one call... every time.   We guarantee you will be  offered the highest level of technical assistance and be satisfied with the quality of our products.

If you need something today, please e-mail us at  sales@GWRauto.com  and we will be glad to quote you on the item.  If you would like to speak directly to a knowledgeable sales representative, please call 1 (800) 266-4497 weekdays, between 2pm and 8PM EST.

Part #

Picture

Price

9310

$535.00

THE MOST COMPLETE ADAPTER SET... CUT ALL TYPES OF ROTORS, INCLUDING COMPOSITE!
Note:  Be sure to compare before you buy, this is the OEM 14 piece kit.
(Most internet sellers only offer a 13 piece kit, it's missing one of the master backing plates)

This is the must have for any brake lathe.  It has 1" hole for most arbors and fits all style rotors (std, composite, etc).  Adds 30lbs to the rotor's mass for a guaranteed 10% smoother cut!
The only adapters guaranteed to smooth surface finishes and eliminate bad cuts, with the fastest set up time in the industry.  These adapters are the system recommended by more OEM's (Ammco, Rels, FMC, etc) because you add 20 to 30 pounds to the rotor mass (weight), plus they allow 360º rotor contact.  We can easily save you up to 50% on this item, don't spend $100's more for the same adapter set.   (Six precisely machined centering cones span the range of 1.84" to 3.85" hub holes)

Note:  Does not require adjusting, periodic cleaning or the replacement of teeth,
like quick chuck type adapters.  Our full centrifugal adapters are the original and eliminate all the wasted time and money required to use other copy cat styles and models.

 

9313

THE MOST COMPLETE ADAPTER SET... CUT ALL TYPES OF ROTORS, INCLUDING COMPOSITE!
This OEM 9 piece kit, takes over where the 9310 above stops.  It has 1" hole for most arbors and is designed to fit rotors on 3/4 and 1 ton light to mid-size truck applications. 
Adds 30lbs to the rotor's mass for a guaranteed 10% smoother cut!

The only adapters guaranteed to smooth surface finishes and eliminate bad cuts, with the fastest set up time in the industry.  These adapters are the system recommended by more OEM's (Ammco, Rels, FMC, etc) because you add 20 to 30 pounds to the rotor mass (weight), plus they allow 360º rotor contact.  We can easily save you up to 50% on this item, don't spend $100's more for the same adapter set.  (Six precisely machined centering cones span the range of 3.75" to 5.5" hub holes)

 

9800

$24.95

Extreme Duty 4-Spring Silencer Band System.  Each spring is packed with a dense Neoprene rod to accept maximum vibrations and harmonics.  This is the best silencer on the planet!

 

0120

$36.95
(each)

or

$34.95
(each w/
3 tools)

Flex-Hone® for Rotors utilizes the patented Flex-Hone® technology to produce the ideal surface finish on automotive and motorcycle disc brake rotors, automotive fly wheels and clutch plates.  Sandpaper, scotch pads, swirl discs, grinding pads or the like all damage the surface because the are following your hands motion, this creates microscopic dips and grooves in the rotor.   Remember, this is the rotor you just spent 10 minutes cutting, trying to create a straight, parallel surface with .001" tolerances.  You must have a cross-hatched finish, not the cross-directional one you have been taught is right.  (If someone says Cross-Directional they are wrong or just misunderstand metal machining processes. Compare the finish on a motor's cylinder, after its re-bored and before you put in a new piston.  Would you ever think of taking a piece of sandpaper or scotch pad to scratch up the walls to create a break-in finish?)

Multiple Undercar Digest "Top Ten" tool winner!

The tools lasted for over 200 sets of rotors, our testing indicated this tool is a great idea;
it's cheaper to use over a long period of time than other brands that are on the market.
Rob Jones   Assistant Manager / Midas Muffler

The net cost per rotor is 1/2 the cost of pads, discs, sandpaper etc, because you need to change them on every single rotor if you don't want to have different finishes on the same vehicle.  That can't be good! Throw out your old sandpaper on a block and get the job done better and more efficiently.  Get more rotors per hone than any abrasive system, proper Ra crosshatch surface finish every usage and rotor hatched in just seconds...  What are you waiting for?

 

3101
and
3102

$134.95

$14.95

AMMCO 1' Arbor and 1" Nut
Ammco Model 2002, 3000, 4000, 4100, 7000 and 7700

6920

$14.95

HD Rubber Silencer w/ Lead Weights
Finest materials available with precise water jet cut tolerances, better that anyone's OEM version.
Fits: Ammco Model 2002, 3000, 4000, 4100, 7000 and 7700, and most any other lathe except on the car models with low clearance

 

9232

$179.00

Brake Lathe Double Tapered Rotor Adapter Cone Set
(5 Adapters that range between 1.322" and 2.897")
Center hole is bored for 1" arbors
(Fits Ammco Model 2002, 3000, 4000, 4100, 7000, 7700 and most all other lathes)

 

5280
and
5290

23.95

29.95

OE Brake Lathe "Wide" Silencer Band for Drums w/Buckles
1-3/4 inch fits most cars parts, while the 2-3/4" is designed for trucks
 (Fits Ammco Model 2002, 3000, 4000, 4100, 7000, 7700 and most all other lathes)

 

6930

$29.95

Brake Lathe "Heavy Duty" (Double Row) Silencer Band for small drums and vented rotors.
 (Fits Ammco Model 2002, 3000, 4000, 4100, 7000, 7700 and most all other lathes)

 

6922
and
6921

$6.95
Set
(Two to a package)

9183

$9.50
Set

Ammco Brake Lathe "Hockey Puck" Silencers Pads
Replacement Set of 2
For use with Ammco model 7075 and 70752 Rotor Silencers

 

185

$28.95

50

$27.95

"OE APPROVED"
A MUST HAVE TOOL FOR SHOPS CUT ROTORS WITH ON CAR LATHES!
This ProCut style Silencer's exclusive patented design, eliminates chatter better than any other silencer on the market designed for On-Car Lathes.  It's been tried, but nothing comes close to the ProCut style BLUE CLIP-ON SILENCER's effectiveness when tuning rotors. This Silencer eliminates chatter at the cutting tips and stays in place until cut is finished. Works on vented & non-vented rotors and will not jam.
Accept no imitations! Get the BLUE CLIP-ON SILENCER, it's the one that works!!!

 

3085
3085R
23682

$13.95

$17.95

$22.95

Polyethylene (aftermarket) and Rubber (OEM) Spindle Boots for Ammco models 3000, 4000
(Note:  Metal #23682 Spindle Ring only works with 3085 Plastic Boots)

 

3087

$9.95

Brake Lathe "Cross Feed" Boot for Ammco models 3000, 4000, 4100, 7000, 7700

 

3086

$9.50

Brake Lathe "Feed Screw" Boot, for Ammco models 3000, 4000, 7000

 

9492

$26.95

Brake Lathe Self Aligning Spacer for 1" Arbors
(Fits most any lathe with a 1" diameter arbor )

 

7996

Ammco Brake Lathe Shear Gear and C-Clip Kit
(Fits models 4000, 4100, 7500)

 

$129.95

OE Ammco Brake Lathe Silencer Frame Assembly for Rotors
(Fits models 4000, 4100 and 7500)

 

Brake Lathe Adapter Centering Springs for Taper Cones and 1 inch Arbors
(Note: Model 3110 fits stock style hollow cone auto size adapters, model #3590 fits stock style hollow cone light truck adapters and the 29591 fits newer style full centrifugal type like 9310 and 9313)

 

Conversion or replacement "Steel" Serpentine Pulley set for most Ammco Models
(I.E. 2000, 4000, 4100, 7000, 7100)
Belts last longer while machine and rotors run smoother, much better than Aluminum OEM Ammco version.   Our kit include OE Pulley's, Serpentine belt and locating pins for a complete installation.
 

380J16

 

4L250

Goodyear OE Serpentine Belt
This is the original belt and the highest quality you can buy.
Don't get stuck with a cheap offshore version, like the one the autoparts store sells.

  Goodyear OE V-Belt
This is the original belt for the older style, standard 3 groove pulley.
• High-strength Vytacord™ tensile members.
• Wingprene-impregnated Wingflex™ envelope.
• Goodyear’s Plioflex® cushion and insulation.
• Dual branded (Classical and FHP part numbers).
• Oil, heat, ozone, and abrasion resistant.

 

34.95
"3850"
Lathe

$9.95
Belt

OEM Ammco Brake Lathe Work Light Replacement Kit
(This new lamp fits most Ammco models, although we have new lamps for all major brands)

 Work Light Repair Kits:   1. Switch and Socket Kit   2. Rubber Dust Boot Kit
(Not Pictured)

 

Brake Lathe Plastic Shield Assembly
(Fit Ammco Model 4000)

Knurled Locking Knob
(Holds steel bracket to lathe base)

 

Brake Lathe Part, Main Switch, To Fit Ammco Model 4000

 

DIAL INDICATOR W/ MAGNETIC BASE
EVERY SHOP DOING BRAKES "MUST" HAVE THIS TOOL!
This is the item we talk about in every seminars we do... to check rotors you must have equipment that can measure run out (warpage) both on the vehicle and on the lathe.  Simply mount the magnet base on a steel surface (lathe or caliper mounting area) and point the indicator to the surface you want to check.. Then adjust the dial bezel to zero and finally rotate the object to determine if it meets specifications. You will save countless hours of wasted time by spending just 30 seconds checking each rotor. Easily determine if you have a bend hub, spindle or hat without having to cut a rotor first... a savings of 10 to 15 minutes at least!

 

Safely and easily stop the flow of water to or from a radiator
or smaller heater hoses, to check for leaks and more.
Stop putting contaminated brake fluid back in to the master cylinder!
One handed operation makes this tool a snap to use, simply slide it over the rubber hose and pull down on the ring around the handles.  By design the jaws won't completely close so you can't damage the hose, unlike other high priced locking tools on the market.  This is an approved and safe tool, everyone needs!

ORDER A SET OF ALL THREE and SAVE BIG...   $18.95

O.E.M. Twin-Cutter Hold Down Nut and Stud Kit
It is impossible to properly cut rotors  when you can't keep the twin cutter from moving, it's a major problem. The OE special nuts are designed to last only a few years and then be replaced, so don't keep fighting with your loose twin cutter head.  (Standard with Ammco model 3000 and 4000 Brake Lathes)

 

$27.95

$25.95
$89.95
$59.95

Spindle Lock Kit
(Standard with Ammco model 3000 and 4000 Brake Lathes)

$99.95

Cut larger rotors with this Lead Screw Extender Kit  (Fits Ammco Model 4000)
Extend the standard feed length about 1", you can machine rotors up to about 15" diameter.
(Included lead adapter, mounting screws and a longer feed table lower guide bar)

$64.95
(Kit)

Advanced Design Replacement Twin Cutter Assembly Head
(Complete New Assembly with Precision Micrometers and Cylindrical Holders)
An extremely high quality part that replaces 6900 units, plus updates your machine to handle larger diameter rotors.  Get rid of your worn and out of tolerance original assembly, while adding 1" additional depth in the throat area.  Precise, new, inch or millimeters micrometers allow easy setting of the depth of cut on inner an outer rotor surfaces.  Making you lathe cut like new will virtually eliminate rotor pulsations and comebacks.
(Fits 3850, 4000 and 7000 series lathes, plus it will upgrade a 3000 model with additional parts)

$595.00

BRING YOU LATHE BACK FROM THE GRAVE WITH GWR'S OE STYLE REBUILD KITS
Parts are exact fit and give you back the tolerances you had when the unit was new!

GWR's "Ammco" Rebuilding Kits

We have three packaged kits that make it easy to return your lathe to like new condition, everything is in one package.  You don't have to worry about missing something, just order one of GWR's three kits and you are set to go.   All parts are guaranteed OE or Better quality.

#65-Basic         #65-Deluxe       #65-Master

 

$ See Below
 

Please note that a service charge of $10 will be added to orders less than $50,
with a minimum net order of $25 (excluding freight).